How to install vinyl siding over wood clapboard

how to install vinyl siding over wood clapboard

Installing vinyl siding over wood siding? Indiana Siding Contractors answer

While vinyl lap siding is the easiest kind to install, it still happens one panel at a time, starting from the bottom starter strip. Once you have attached the first board to the starter strip, you will want to check that it was level in its installation. The ends are then pushed into the J-channel on the ends. The most common practice when installing vinyl siding over existing wood shingles or clapboard is to first put up rigid foam or fan fold. However,this means adding 1/2? padding, and another 3/4? or 1? of siding to your existing wall.

People come to us with a lot of questions with regards to vinyl siding, and what is possible to do with it, which is why we put together this neat little article to clarify some things and hopefully help you make the most informed decision. Keep in mind that this article will have less general information about vinyl siding than the hyperlinked article, which is our attempt at answering everything you need to know about the siding material. All you have to do to get started is simply fill out the form below.

Get Free Quotes Now. We will not contact you with anything else. Our specialists are currently reviewing your case and will get back to you shortly.

The answer to that question is yes. Yes, you can put vinyl siding over siidng wood siding assuming its condition is still good. Any bad boards will need to be replaced. Other things including potential trim or windows that have been installed will need to be taken out so that woov can proceed with the installation. In most cases you can put new siding directly on top of old siding without having to remove the old siding first, and in addition it will in fact add an addition layer of insulationthereby helping lower your energy bill.

Foam board is, however, often added oveg order to help level out the wall when it has certain problems with it. There are also states that provide you with tax credits when you insulate your home better, and your existing siding could make you eligible for those. Is it better to leave existing siding on or to take it off? The curling of the existing wooden siding would cause the wall to look curvy.

Fiber cement siding can however not be left on, as well as some other types of siding such as metal siding or previous vinyl. Make sure to speak to a imstall contractor to see what their recommendation is in your specific case. Warp, curing, delamination and rot are all things that may require that it be completely replace.

If there have been previous water leaks or water infiltration of any kind, those could have left damage requiring new support.

Termites, damage how much is it to get marry in the courthouse wood peckers, rodents and pests are a thing that should be addressed also. If you leave on the existing material, the project will also take less time. Those characteristics are in fact very appealing to most homeowners. But why would you actually choose to install vinyl since you already have wood siding installed on your home?

As you can see, vinyl by itself already has a lot of benefits, but how does vinyl compare to wood? Wood is a better insulator in general than normal vinyl is, which is why it is still such a popular material when it comes to adding it to new construction.

To counteract that, a lot clapbard people choose insulated vinyl or make sure that their home otherwise has all the insulation that they need with either how to install vinyl siding over wood clapboard wool, cellulose, SPF, EPS or fiberglass tto. New construction that uses vinyl will be installed on plywood typically and insulation and a moisture barrier is also used in order to keep your home well insulated. The process that an installer will usually follow is listed below. The state of the wood is important, especially because if it is poor condition, it can continue deteriorating underneath when it has been installed, which would cause further problems for the outer material at a later stage.

The inspection should also include actually making sure that all the boards are steadily fastened to either wall sheating or studs. Windows, doors and trim must be taken off at this point.

Any what is a criminal record in south africa surfaces must be fixed in order to prepare vunyl the new installation.

Gutters and outdoor light fixtures also pose potential problems in the process and should also be taken off. The furring strips are nailed to the wall studs with moisture and rust-resistant nails.

A polyethylene widing barrier is one of the more common options. Broad headed nails are used to secure the moisture barrier on top of the rigid foam. The nails have plastic washers below the heads to protect the polyethylene. In order to ensure that the moisture barrier works, the seams are sealed. Make sure that the moisture barrier you choose to clapboarv with live up to the building codes in your local area. Trim coil, roofing felt or house wrap are other materials that homeowners go with as a moisture-resistant barrier.

Corners should vinyll flashed with a water-resistant material 10 inches to each side of the corner to ensure protection. Since the vinyp are now thicker than they used to be, so do the frames of doors and windows also need to be. If you have other types of openings, these also need to be adjusted to the thicker wall so that it looks nice and provides protection against the inner layers too. The difference in thickness comes down to the additional layers that were added in the process that included vinyl panels, the added insulation, and foam boards.

Doors and windows will need new flashing to provide moisture-resistance, and this should be made from a non-corrosive metal to make sure moisture stays out. All other utilities sticking through the wall will also need to get ovef flashing, including the faucets and more. The initial fastening strip is a key part of the installation since it creates the starting point for the vinyl siding installation.

If this part starts out not being level, clpaboard rest of the installation also will not be. The panels interlock which is why all unevenness will be seen later clapbkard so you should start out by getting this properly installed. Draw a chalk line around the house roughly an inch above the lowest part of the wood siding. The installation of such a strip will help strengthen the installation and is where the lowest panel will be attached to. Vinyl siding is installed with a gap on both sides since it tends to expand ovef weather changes, and leaving this oevr will allow for that expansion to not cause any problems.

When the nails are hammered to the backer board, do so in the middle of the nailing slot. While this may sound counter-intuitive, it insatll be done so as to allow the material to expand and if done correctly it will let the material slide within the limits of the nailing slots.

An important part of the installation is in fact choosing the right nails. Your siding material will be exposed to water, wind and maybe even frost for many sdiing to come, which also creates certain how to install vinyl siding over wood clapboard for the nails to avoid boards going loose and stopping the nails from corroding or rusting.

Yes, you probably guessed it. Stainless steel nails are the more expensive option of the two. You can how to build a pole building shed use either nails, what month was the constitution signed or staples to secure it in place.

Sicing a tiny amount of space, about the space of a nickel that will still let the panels be flexible. If the siding was simply installed without having anything securing it at the ends, it would become very vulnerable to anything catching on to it and easily tearing ijstall off. J channels are sometimes referred to as corner channels also, and their name comes from the shape that they have.

The J-shape allows it to properly hold things in place. These are installed sidig on the corners. Photo credit: Iver Specialty Siding. Remember that the installation should allow for enough space for vinyl to expand. Utility trim is used in combination with the J channels around windows and below roof soffits.

While vinyl lap claboard is the easiest kind to install, it still happens one panel at a time, starting from the bottom clapboarr strip. Once you have insyall the first board to the starter strip, you sidingg want to check that it was level in its installation.

The ends are then pushed into the J-channel on the ends. Hooray, your first vijyl is woood in place once everything is level and the foundation clapboaard been laid for the installation to continue. You may not always be able to have a panel span the whole length of the wall, which means the different panels will need to overlap. Even when overlapping, the boards should be able to move from side to side with the nails being attached in the dood of the holes.

You are also installing this material to provide curb appealand in that process you will want to ensure that the seams between overlapping panels sidung not align vertically. To keep this from happening, the installer will need to cut the siding accordingly. Panels are also cut so that they can fit around windows or doors. While not the best solution, a utility knife suffices to get this job done. The easiest way to mess up your installation is by not having the tops stay aligned going around the house.

The easiest way to hoe everything is level is therefore not to start on one side of the house and immediately work your way to the top for it but rather working around the house instead. It simply makes it easier for you to ensure continuity and that corner panels are aligned. What it does is it creates a surface that can easily lock in with the utility trim that you installed around the windows.

The lugs are then pushed into the utility trim to help keep the board in place. While installing the big individual boards yourself may be manageable, the process becomes significantly harder once you get to the more difficult siring such as windows. Please Choose The Type of Service. Next Step. It only takes 2 minutes to fill out the form. You are almost done — fill out this last step.

This information makes sidign easier to coordinate with pros. Please fill this field. Invalid zip code. Invalid email. Invalid phone number. Invalid address. Thank you!

Cookie banner

While covering lap siding with vinyl is an option for some siding, other varieties of lap siding can't be covered by vinyl. Generally, the best idea is to remove any existing siding from your exterior walls before installing the vinyl siding. This goes for fiber cement, hardwood and masonite siding. Jun 13,  · Many people think installing vinyl siding over wood siding, heck installing vinyl siding in general, is an easy task. Sure, it’s duty-free, resists insects, rotting, and doesn’t need to be painted. Before moving forward we always say, DON’T SELF DIAGNOSE your siding issues. Sep 14,  · My aluminum siding is old, faded and dented, so I've decided to replace it with vinyl. I was assuming under the aluminum there would be a flat surface, but instead the aluminum siding has a profiled back insulation that gives the siding a flat back and was applied directly over 8" clapboard.

Home » Siding Contractors » Installing vinyl siding over wood siding? Indiana Siding Contractors answer. Many people think installing vinyl siding over wood siding, heck installing vinyl siding in general, is an easy task. You never want to get caught doing diy on a problem you thought was only minor.

Call the Indiana Siding Contractors for all your siding repair needs. On older homes, any old siding vinyl or metal needs to be removed. On that note, the first thing you have to check is if the wood on your home is sound. If none exists under the wood, then you will have to take a major step back on this project and have your house wrapped with the proper material.

Again, it takes serious preparation and expert knowledge. June 13, Siding Contractors. Tags: Indianapolis , Siding Contractors.

Post Your Thoughts Cancel. How to Install Fiber Cement Siding. Need Support? Help is just a click away! Community Exteriors, Inc. Have general questions? Simply, let us know your issue to the best of your ability and we will get back to you ASAP! We are here to help!

1 thoughts on “How to install vinyl siding over wood clapboard

Add a comment

Your email will not be published. Required fields are marked *